HELIX 206 Direct
One for all – no matter if 3-way, 2-way or subwoofer application, the 6-channel amplifier M SIX will always be the right choice.
With generously 100 Watts RMS per channel into both 4 Ohms and 2 Ohms load this amp really gets your speaker cones going despite its super-compact dimensions. On the other hand the M SIX stays totally cool thanks to its highly efficient Class D design topology. And even bridged configurations are possible, delivering up to 3 x 200 Watts RMS of clean and undistorted output power.
In addition a comprehensive and stunningly practical feature set leaves nothing to be desired. And finally the perfect sound tuning is no big deal thanks to its integrated crossover with all its setup options.
Features
- Small footprint Class D amplifier with high output power of 100 Watts RMS @ 4 and 2 Ohms load
- Start-Stop capability down to 6V supply voltage
- 6-channel lowlevel input
- Integrated, active crossover with highpass, lowpass, bandpass and subsonic
- “Input mode” switch for channel E & F for flexible input signal routing
- SMD (Surface Mounted Device) manufacturing technology combines minimum space requirement with maximum reliability
- Exclusive, extremely compact and clean design with illuminated HELIX-logo and low heat dissipation thanks to extraordinary efficiency
Special features:
Start-Stop capability
The switched power supply of the HELIX M SIX assures operation even if the battery’s voltage drops down to 6 Volts during engine crank.
Specifications
| Power RMS ≤ 1% THD+N @ 14.4 V | |
|---|---|
| - @ 4 Ohms | 6 x 100 Watts |
| - @ 2 Ohms | 6 x 190 Watts |
| - @ 1 Ohm | - |
| - bridged @ 4 Ohms | 3 x 380 Watts |
| - bridged @ 2 Ohms | - |
| Max. output power per channel* | Up to 240 Watts RMS @ 2 Ohms Up to 480 Watts RMS @ 4 Ohms bridged |
| Amplifier technology | Class D |
| Inputs | 6 x RCA / Cinch 1 x Remote In |
| Input sensitivity | 1 - 8 Volts |
| Input impedance | 6 kOhms |
| Outputs | 6 x Speaker output |
| Output voltage RCA / Cinch | - |
| Signal converter for digital input | - |
| Frequency response | 10 Hz - 22,000 Hz |
| Bass boost | - |
| Highpass | - |
| Lowpass | - |
| Bandpass | - |
| Subsonic | - |
| Phase | - |
| Slope high- / lowpass | - |
| Slope subsonic | - |
| Slope subsonic / lowpass | - |
| Signal-to-noise ratio (A-weighted) | 103 dB @ full power |
| Distortion (THD @ 1 kHz, 1 W into 4 Ohms) | < 0.003% |
| Distortion (THD+N @ 1 kHz, 1 W into 4 Ohms) | < 0.015 % |
| Distortion (THD @ 100 Hz, 1 W into 4 Ohms) | - |
| Distortion (THD+N @ 100 Hz, 1 W into 4 Ohms) | - |
| Damping factor | 70 |
| Operating voltage | 10.5 - 16 Volts (max. 5 sec. down to 6 Volts) |
| Idle current | 1,100 mA |
| Fuse | 3 x 25 A LP-Mini-fuse (APS) |
| Power rating | DC 12 V ⎓ 93 A max. |
| Operating temperature range | -40 °C to +70 °C |
| Additional features | Start-Stop capability, Clipping LED, DirectDSP inputs |
| Dimensions (H x W x D) | 41.5 x 263 x 118 mm / 1.63 x 10.35 x 4.65” |
Installed by Audio Edge
We sell every product as part of a system designed for your vehicle — consultation, installation, and tuning included. Tell us what you drive and we’ll tell you what this can do in your car.
Proof
Used in these builds
Let’s talk about your car
Tell us what you drive and what you want it to sound like. We’ll come back with a plan — gear, fabrication, timeline, and a real number.